T1K-512 DMX Controller Software: DMX512 and Pixel Chips

Program the T1K-512 DMX512 single-channel controller with LEDEdit Pro 2026: 19 chip profiles including UCS512B3/C3/C4, SM16512, WS2801, LPD6803, P9813 and RGBW, plus DMX address config export.

Buy LEDEdit Pro 2026 — €99 All controllers

The T1K-512 is the DMX512 controller of the LEDEdit 2026 series: one output with up to 512 LEDs and chip profiles for DMX-addressable ICs such as UCS512 and SM16512, as well as classic SPI-style chips.

T1K-512 in LEDEdit Pro 2026

  • 1 output, up to 512 LEDs in the export profile.
  • 19 export-ready chip profiles, three of them RGBW (TM1914, TM1814, SM16704).
  • DMX address configuration export for fixtures that need addresses written.
DMX address configuration export dialog in LEDEdit Pro 2026
Output → Export DMX Address Config… writes the DmxSet.led address files.

Example: architectural wall washers

Twenty DMX wall-wash fixtures along a facade, each with a UCS512 chip:

  1. Place one LED per fixture in the LED Layout Creator, in cable order.
  2. Build a slow colour show — Breathing Bands, Aurora Panel or palette chases work well for facades.
  3. Export the .led with the T1K-512 family and the UCS512 profile, and write the address config if your fixtures need it.

Tips

  • Keep fixtures in the same order as the DMX cable run.
  • Use Inspect .led File… to double-check an address file before you climb the ladder.

Chip profile notes: WS2811 / WS2812B

The T1K-512 family does not list a dedicated WS2811/WS2812B profile — its 19 chips focus on DMX-addressable and SPI ICs: UCS512B3 / UCS512C3 / UCS512C4, SM16512, WS2818A / WS2818B, SM16704 / TM1914 / TM1814 (RGBW), WS2801, LPD6803 / LPD1886, SM16716, P9813, TM1829/TM1814 and others from data/lep_controllers.json family ledit2026_t1k_512. For standard WS2811 / WS2812B pixels (single-wire 800 kHz, 24-bit RGB) prefer the T-U series (WS2811 profile) or T-1000 family (T-1000-WS2811 / WS2812). If your DMX fixture uses WS2812B-based LEDs behind a DMX decoder, keep the T1K-512 DMX chip (e.g. UCS512) and set colour order GRB for WS2812B tails and RGB for WS2811, then verify with wrong colours fix. Flicker not colour swap means wrong chip timing.

5-step export to SD card (T1K-512 DMX)

  1. Map fixtures — In LED Layout Creator place one LED per wall-washer in DMX cable order on port p1. Set Max LEDs/port = 512 and confirm 20 of 512 used.
  2. Build slow show — Add a layer, drop Breathing Bands or Aurora Panel with a slow palette, and check the facade in per-LED preview — see the video tutorial for the preview workflow.
  3. Choose chip & addresses — Output → Export LEDEdit .led → family T1K-512 + chip UCS512B3 / UCS512C3 / SM16512 (or TM1914 for RGBW). Set colour order and FPS.
  4. Write DMX config + .led — If fixtures need addressing, also run Output → Export DMX Address Config… (writes DmxSet.led) and Inspect .led File… to verify. Then Write to SD Card or copy both files to the card.
  5. Test — If fixtures stay dark, see SD-card not playing and last LEDs dark (512 limit), and DXF + AVI fallback for legacy DMX hardware. Re-check DMX start address and channels per fixture.

FAQ

Which WS2811 / WS2812B chip for T1K-512?No dedicated WS2811/WS2812B profile here — this family focuses on DMX (UCS512, SM16512) and SPI chips. For pure WS2811/WS2812B use the T-U series WS2811 or T-1000 WS2811 / WS2812 profile. If your DMX decoder drives WS2812B LEDs, keep the DMX chip and set colour order GRB.
How many LEDs and how to address DMX fixtures?Up to 512 on its single output. For DMX addressing run Output → Export DMX Address Config… to write DmxSet.led address files, then verify with Inspect .led File… before climbing the ladder.
Why do colours look wrong on DMX washers?Swapped reds/greens = colour order (GRB vs RGB) — see wrong colours fix. No light or wrong fixture = address / channels per LED or wrong chip timing; re-check the fixture datasheet and the T1K-512 chip list.

Address your T1K-512 with LEDEdit Pro

512-LED DMX single output, 19 chip profiles and DmxSet export — LEDEdit Pro 2026 for DMX wall washers. Lifetime €99.

Buy LEDEdit Pro 2026 — €99 Watch demo

T1K-512 in LEDEdit Pro 2026

ProfileOutputsLEDs per outputChip profilesExport-readyData formats
T1k-51215121919DMX512, RGB, RGBW

Data from the app's controller catalog. "LEDs per output" is the export profile's pixel limit; also check your controller's manual.

T1k-512: all 19 chip profiles
  • SM1670*,UCS19**
  • TM1809
  • SM16716
  • P9813
  • LPD6803
  • LX1003
  • WS2801
  • LPD1886
  • TM1914
  • P9883/P943
  • TM1926
  • TM1829
  • TM1814
  • SM16512
  • UCS512B3
  • UCS512C3,UCS512C4
  • WS2818A
  • WS2818B
  • SM16704

  1. Map your LEDs in the LED Layout Creator or import a DXF layout, with one port per controller output.
  2. Build the show with layers, clips and scenes on the timeline.
  3. Open Output → Export LEDEdit .led…, choose the T1K-512 family and the chip type of your pixels.
  4. Check the preflight (controller, chip, colour order, scenes, frame rate, outputs, LEDs) and click Export.
  5. Copy the files to the SD card, or use Output → LEDEdit Tools → Write to SD Card….
LEDEdit Export dialog in LEDEdit Pro 2026 for T1K-512
Pick controller and chip; the preflight confirms everything before anything is written.
Controller does not play the file? Check family, chip and colour order. If it still fails, export DXF + AVI and build the .led in the free LEDEdit version that works with your controller — step-by-step guide.

FAQ

Which chips does the T1K-512 profile support?
19 profiles: SM1670* / UCS19**, TM1809, SM16716, P9813, LPD6803, LX1003, WS2801, LPD1886, TM1914, P9883 / P943, TM1926, TM1829, TM1814, SM16512, UCS512B3, UCS512C3 / UCS512C4, WS2818A, WS2818B and SM16704.
How many LEDs per output?
Up to 512 on its single output in the export profile.
Can LEDEdit Pro write DMX address files?
Yes. Output → Export DMX Address Config… writes separate DmxSet.led address/config files, and Output → LEDEdit Tools → Inspect .led File… reads them back.